How can you fix ylod

Customer ratings and reviews. The minimum purchase order quantity for the product is 1. Add to cart. Add to wishlist. Availability date:. Tweet Share. We repair this fault by resoldering the consoles mainboard using our Computer controlled Dark Infrared BGA rework stations, these safely re solder reflow the main board to exact manufacturers specifications. This ensures that your consoles main board is not damaged or stressed during this process.

One of our Computer Controlled Dark Infrared reflow stations. We will fully resolder your consoles main board, give your console a full service and upgrade the thermal compound used within the PS3. For your peace of mind we give you three months warranty. Sent my original pride and joy PS3 for a repair after it got the dreaded ylod.

After posting it off to console wizard it was discovered that the CPU was beyond repair so that was the end of it. Absolutely gutted but the guys at console wizard tried their very best and a full refund was given and my PlayStation was sent back to me in no time.

It didn't work out for me this time but I would recommend console wizard to anybody who needs a repair. The team went above and beyond. Be sure you are prying up on the retaining flap, not the socket itself. Pull the control board ribbon cable straight up and out of its socket on the motherboard. Remove the two 12 mm Phillips screws securing the control board to the lower case. Remove the following eight screws securing the motherboard assembly to the lower case:. Use the flat end of a spudger to pry the hard drive bay cover away from the lower case.

While depressing its locking mechanism, pull the AC-In connector out of its socket on the power supply. Pull the AC inlet out from the bottom of the rear cover, minding any of its cables that may get caught. While lightly pulling the rear cover away from the logic board assembly, use the flat end of a spudger to release the clips along the top and bottom edges of the rear cover.

Remove the two 9 mm Phillips screws securing the memory card reader to the chassis. Lift the power supply by its front edge to clear the two posts attached to the motherboard. Remove the four The heat sink may still be held in place by the thermal paste. If this is the case, gently pry the heat sink away from the motherboard housing. Make sure to not bend the copper piping on the heat sink.

Never applied thermal paste before? Our thermal paste guide makes it easy. If you're following the YLOD repair guide, stay tuned for where to apply the replacement thermal paste. Flip up the flap on the memory card reader ribbon cable socket and remove the ribbon cable.

The PRAM socket is delicate and has the potential to break off the motherboard. If possible, hold down the socket as you disconnect the PRAM battery cable. Rotate the PRAM battery slightly counter-clockwise and remove it from the motherboard assembly.

Remove the two 3. Remove the two 8. Using your fingers or the flat end of a spudger, remove the old thermal pads on the logic board as indicated:. Small rectangular thermal pads located on the underside of the board, as highlighted in the second picture. Some of the smaller thermal pads may be attached to the metal casing that surrounds the motherboard rather than the motherboard itself.

Set the heat gun to "Low", and let it run for a few seconds to reach operating temperature. Holding the motherboard upright, warm up the entire board with the heat gun.

The board should be warm, but not too hot. The support should be something that can resist temperatures upwards of degrees Celsius. Suggestions: scrap lumber, old books, cardboard box. In the next few steps, you will be reflowing the solder under the chips marked in red.

Once you begin reflowing the chips, do not touch or move the motherboard until it is completely cool. Doing so can render the motherboard irreparably damaged. Using a circular motion, evenly heat using low heat each of the four areas for roughly 25 seconds each. Continue heating the chips using the same circular motion as described above, for about 25 seconds each. Step 13 As indicated in the photos, use the nylon spudger to delicately lift the latch. Step 14 Now gently grasp the power board cable and remove it from its connector.

Step 15 Unscrew the 2 cross headed screws circled in red in the photo. These secure the power board to the internal frame of your PlayStation 3 Fat. Step 16 Now grasp the power board and remove it from its placement.

Step 17 Unscrew the 2 screws circled in red in the photo. Step 18 You can now grasp and remove the bracket for the power supply board from its placement. Step 19 Now unscrew the 6 cross headed screws circled in red in the photo. Step 20 Now remove the hard drive access door using the nylon spudger. Step 21 Lift the internal frame metal structure in order to remove it entirely.

Step 22 Delicately unplug the power supply cable AC-In on the back of the power supply block. Step 23 Unscrew the cross headed screw circled in red in the photo.

Step 25 Delicately unplug the power supply cable DC-In on the front of the power supply block. Step 26 Unscrew the 5 cross headed screws circled in red in the photo. These secure the metal power supply block to the internal frame of your console. Step 27 Delicately lift the power supply block to remove it from its place. Step 28 As indicated in the photos, use the nylon spudger to unclip the two plastic brackets.

Don't try to remove the front panel of your PS3 now, it's still attached by other brackets. Step 29 Turn over your PlayStation 3. Step 30 Unclip the final bracket on the left holding the rear panel to your PS3. Step 31 Now, very delicately, lift off the rear panel. You shouldn't feel any resistance. Step 32 With the nylon spudger move the fan cable delicately out from under the black plastic clip.

Step 33 Unplug the fan from the power supply. Step 34 Unscrew the 4 cross headed screws circled in red in the photo. Step 35 Remove the first support bracket using the nylon spudger. Step 36 Do the same for the second bracket. Step 37 Now lift the radiator heat sink up to delicately remove it from its placement. Step 38 Using a nylon spudger, delicately lever up the antenna connector in order to disconnect it. Step 39 Move the antenna cable aside to prevent it interfering with future steps.

Step 40 Now use the cross headed screwdriver to unscrew the 4 screws circled in red in the photo. Step 42 Using the nylon spudger, lift the latch for the connector carefully, releasing the cable. Step 43 Then disconnect the cable carefully, no resistance should be felt during this step.

Step 45 Now lift the mother board in order to remove it completely. Step 47 With a clean cloth, now clean off the thermal paste residue. Step 48 Do step 46 again, applying a few drops of ArctiClean 1 solution on the second processor graphics.

Step 49 Still using the cloth, clean the residue dissolved by the ArctiClean 1 solution.